Guest Post by Deborah Cooke (Abridged from a version originally published on www.deborahcooke.com)

Book charms are adorable and readers love them. I’ve bought them in the past from Etsy vendors, but when I realized I needed at least 100 of them for an event last August, I decided to try making my own.

A big part of this decision was that I found little blank books in the dollhouse section at the craft store. They have paper pages and little covers, which are so much more realistic than book charms made of clay. Since these look like little hardcover books, I decided to make slipcovers for them (instead of just gluing my front cover on the book). This is, of course, the Hard Way, but I think the result is worth the trouble.

The tricky bit is getting the proportions right on the printed slip cover. I measured around the book and created a template (using the free online graphics software Canva). I started with the POD cover of one of my books since that image is a full wrap. (That means it includes the spine and back cover)

Remember that you need to have the right to work with the copyrighted cover image. If you’re indie-published and paid for the cover, you’ll likely have that right. If your book was published by another publisher, you might not. Be sure to check.

The proportions are different between the actual book and the book charm: the spine is thicker on the mini-book. I tried a number of solutions, but the best one turned out to be this: I cropped the front cover and positioned it, then did the same for the back cover. I cropped only the title from the spine—it’s usually a third or half the height of the spine—then made it large enough to fill the height. This also made it much wider and helped with that blank space. The resolution diminished, but these will be tiny when they’re printed.

With some covers, I was able to size the front and back larger than the trim size without losing any type. This made the recognizable cover image larger. When possible, I also chose a colour for the background on the template that would blend into the actual book cover image.

Also, because I made a slipcover, I had endpapers, which meant locations for more information. This was part of my diabolical plan. On book charm covers, the type is really small and often illegible. Plus I like having my website url on everything I use for promotion. I put my website url on one endpaper and the book title on the other. Above and below are screenshots of the finished slipcovers for two of my books.

Once the slipcover images were downloaded, I used a Word document and Inserted Picture from File so that the covers were three across. I got eight rows on the page. If you’re like me and use cheap paper in your printer on a daily basis, you might want to invest in a smoother and whiter grade of paper stock. You will use up printer toner with this project if you’re making any quantity of charms, so get a toner refill while you’re at the office supply store.

I used clear Avery Labels (intended to be used for shipping labels – Avery 7664) as my laminate. There are six labels on a page and a label will cover six book covers, but I found that working smaller was easier. I cut each label in half, which is enough for three book covers, touched down one edge then smoothed it across the covers. Fast. Practice makes perfect! I used a burnisher to make sure it was smoothly applied.

Next, cut the book covers apart. If they’re lined up perfectly, this is pretty easy to do with a cutting mat, straight edge, and an X-acto knife. Once mine were cut, I folded down the front end paper, then wrapped one cover around one book before folding down the back end paper. (The books do vary a little bit in size, so you need to match cover to book, one at a time.) Once everything looks good, glue the endpapers to the inside book cover. They’re the same kind of paper, so it should make the best seal and I like that the slipcover lifts off the outside of the book a bit, like a real slipcover. I used a small gluestick, which minimized the chance of my getting glue in the wrong place. Put a weight on the book or clamp it until it dries.

Once the glue was dry, a Dremell drill press was used to make the holes. I put a jump ring on each one, then since these are charms for a bracelet, I added a clasp before closing the jump ring. This makes it easier for readers to add the charm to their bracelet at the event. The finished books each get their own bag. (The dollar store will be your friend with this project.)

When I posted on Facebook that I was making book charms, readers became quite excited. When I showed the finished charms, some people wanted to buy them—which is a mark of very good swag!